The air compressor is generally used in large gas volume occasions. The matched motor power is relatively large, the frequent start and stop has a great impact on the power grid, the current is large during start-up, the heating capacity of motor coil is also relatively large, and the motor is easy to burn if it is started and stopped too frequently. The following describes how to avoid frequent start and stop of air compressor.

1、空氣壓縮機機組油系統清洗調整合格，油質化驗合乎要求，儲油量適中。檢查主油箱、油過濾器、油冷卻器，油箱油位不足則應加油。檢查離心空壓機油溫若低于24℃，則應使用加熱器，使油溫達到24℃以上。油冷卻器和油過濾器也應充滿油，放出空氣，油冷卻器與過濾器的切換位置應切換到需要投用的一側。

1. The cleaning and adjustment of the oil system of the air compressor unit are qualified, the oil quality test meets the requirements, and the oil storage is moderate. Check the main oil tank, oil filter and oil cooler. If the oil level in the oil tank is insufficient, add oil. Check the oil temperature of centrifugal air compressor. If it is lower than 24 ℃, use heater to make the oil temperature above 24 ℃. Oil cooler and oil filter shall also be filled with oil and air shall be discharged. The switching position of oil cooler and filter shall be switched to the side to be put into use.

2、檢查空氣壓縮機主油泵和輔助油泵，確認工作正常，轉向確。油溫度計、壓力表應當齊全，量程合格，工作正常。用干燥的氮?dú)獬淙胄顗浩髦?，使蓄壓器?nèi)氣體壓力保持在規定數值之內。調整油路系統各處油壓，達到設計要求。檢查油系統各種聯鎖裝置運行正常，確?？諌簷C(jī)的正常穩定。

2. Check the main oil pump and auxiliary oil pump of the air compressor to confirm that they work normally and turn correctly. The oil thermometer and pressure gauge shall be complete, with qualified measuring range and normal operation. Fill the accumulator with dry nitrogen to keep the gas pressure in the accumulator within the specified value. Adjust the oil pressure of the oil circuit system to meet the design requirements. Check that various interlocking devices of the oil system operate normally to ensure the normal and stable operation of the air compressor.

3、將工藝氣體管道上的閥門按起動要求調到一定的位置，一般空壓機的進出口閥門應關閉，防喘振用的回流閥或放空閥應全開，通工藝系統的出口閥也應全閉。各類閥門的開關應靈活準確，無卡澀。

3. Adjust the valve on the process gas pipeline to a certain position according to the starting requirements. Generally, the inlet and outlet valves of the air compressor shall be closed, the return valve or vent valve for anti surge shall be fully opened, and the outlet valve to the process system shall also be fully closed. The switches of various valves shall be flexible and accurate without jamming.

以上就是避免空氣壓縮機頻繁起停的原因，還有更多的新聞資訊，請繼續關注網站，我們會不定時更新相關的新聞資訊供大家進行參考，敬請期待。

The above is the reason to avoid frequent start and stop of air compressor. For more news information, please continue to pay attention to the website. We will update relevant news information from time to time for your reference. Please look forward to it.