国产精品一区二区久久不卡,婷婷伊人久久大香线蕉AV,A级黑粗大硬长爽猛出猛进,无码A∨高潮抽搐流白浆国产,欧美V亚洲V综合V国产V

行業新聞

當前位置:首頁 > 新聞中心 > 行業新聞

干燥機的出口露 點不合格的原因?

來源:http://owlshollowfarm.com/   日期:2021-06-02   瀏覽量:0
TAG:山東制氮機,山東干燥機,山東螺桿鼓風機,山東空壓機,山東自動排水器
壓縮空氣的含水量多少一般用壓力露 點來表示,露 點越低,表示含水值越小,干燥機的干燥效果越好。在工業中,由于各種用氣設備及工藝流程的不同,需要有不同壓力露 點的壓縮空氣干燥設備為用戶提供選擇的可能。有的要求壓力露 點達到-20℃,有的要求壓力露 點不低于-40℃,還有的壓力露 點要求在-70℃左右。
The water content of compressed air is generally expressed by pressure dew point. The lower the dew point is, the smaller the water content is, the better the drying effect of the dryer is. In industry, due to the difference of various gas equipment and process flow, compressed air drying equipment with different pressure dew point is needed to provide users with the possibility of choice. Some require that the pressure dew point should reach - 20 ℃, some require that the pressure dew point should not be lower than - 40 ℃, and some require that the pressure dew point should be about - 70 ℃.
干燥機出口露 點不合格的原因:
Causes of unqualified dew point at dryer outlet:
1、干燥機出口露 點過高
1. Too high dew point at dryer outlet
2、超出流量值和超過設計條件,在配置吸附式干燥機時應根據空壓機排氣量和工作流量設計。
2. If the flow value exceeds the design condition, the adsorption dryer should be designed according to the air compressor exhaust volume and working flow.
3、干燥劑沒有吸附效果,需更換濾芯
3. The desiccant has no adsorption effect and the filter element needs to be replaced
4、氣流進入干燥機前沒有預處理除去液態水,壓縮空氣進入干燥機前應進行液態水預處理,否則超過吸附劑的吸附能力,吸附劑飽和后將失去吸附效果。
4. There is no pretreatment to remove the liquid water before the air flow enters the dryer. The liquid water should be pretreated before the compressed air enters the dryer. Otherwise, it will exceed the adsorption capacity of the adsorbent and lose the adsorption effect after the adsorbent is saturated.
5、干燥機使用壽命已結束
5. The service life of the dryer is over
壓縮空氣干燥機(干燥機|吸干機)是壓縮空氣系統的重要組成部分,常見的壓縮空氣干燥機有冷凍式干燥機和吸附式干燥機。貝騰模芯干燥機是兩者的升級版,能徹 底解決壓縮空氣含水問題,幫助企業提高壓縮空氣品質,從而提高生產工藝,降低生產成本。
Compressed air dryer (dryer | suction dryer) is an important part of the compressed air system. The common compressed air dryers are freeze dryer and adsorption dryer. Beiteng mold core dryer is an upgraded version of the two, which can completely solve the problem of water content in compressed air, help enterprises improve the quality of compressed air, so as to improve the production process and reduce production costs.

上一篇:干燥設備的工作流程和工作原理是怎樣的
下一篇:螺桿空壓機教大家如何選擇質量好的螺桿空壓機配件?

国产精品一区二区久久不卡,婷婷伊人久久大香线蕉AV,A级黑粗大硬长爽猛出猛进,无码A∨高潮抽搐流白浆国产,欧美V亚洲V综合V国产V